Back to Contents Page

Memory, Optical Drive, and Mini PCI Card

Dell™ Inspiron™ 1300/B120/B130  Service Manual

  Memory

  Optical Drive

  Mini PCI Card


Memory

Removing the Memory Module

CAUTION: Before working inside your Dell™ computer, read the safety instructions in the Product Information Guide.
CAUTION: To prevent static damage to components inside your computer, discharge static electricity from your body before you touch any of your computer's electronic components. You can do so by touching an unpainted metal surface.
NOTE: Memory modules purchased from Dell are covered under your computer warranty.
  1. Follow the instructions in Before Working Inside Your Computer.

  2. Ground yourself by touching one of the metal connectors on the back of the computer.

NOTE: If you leave the area, ground yourself again when you return to the computer.
  1. Turn the computer over, loosen the captive screws on the memory module/Mini PCI cover, and then remove the cover.

 

 

1

captive screws (3)

 

 

NOTICE: To prevent damage to the memory module connector, do not use tools to spread the memory-module securing clips.
  1. If you are replacing a memory module, remove the existing module:

    1. Use your fingertips to carefully spread apart the securing clips on each end of the memory module connector until the module pops up.

    1. Remove the module from the connector.

1

memory module

2

securing clips (2 per connector)

 

 

Replacing the Memory Module

  1. Ground yourself and install the new memory module:

    1. Align the notch in the module edge connector with the tab in the connector slot.

    1. Slide the module firmly into the slot at a 45-degree angle, and rotate the module down until it clicks into place. If you do not feel the click, remove the module and reinstall it.

1

memory slot notch

2

memory slot tab

 

 

  1. Replace the memory module/Mini PCI cover and tighten the screws.

NOTICE: If the cover is difficult to close, remove the module and reinstall it. Forcing the cover to close may damage your computer.
  1. Insert the battery into the battery bay, or connect the AC adapter to your computer and an electrical outlet.

  2. Turn on the computer.

As the computer boots, it detects the additional memory and automatically updates the system configuration information.

To confirm the amount of memory installed in the computer, click the Start button, click Help and Support, and then click Computer Information.

Optical Drive

Removing the Optical Drive

CAUTION: Before working inside your Dell™ computer, read the safety instructions in the Product Information Guide.
NOTICE: To prevent damage to devices, store them in a safe, dry place when they are not installed in the computer. Avoid pressing down on them or placing heavy objects on top of them.
NOTE: If your computer shipped with a device security screw and the screw is not installed, you can remove and install devices while the computer is running and connected to a docking device.
  1. If you want to remove the optical drive while the computer is turned on, double-click the Safely Remove Hardware icon on the taskbar, click the device that you want to eject, and click Stop. Otherwise go to step 2.

  2. Close your display and turn the computer upside down.

  3. Use a Phillips screwdriver to remove the M2.5 x 8-mm screw from the indention labeled with a lock symbol ( ).

  4. Using a screwdriver or some other type of probe, push the notch where the device security screw was removed toward the outside of the computer.

  5. Pull the device straight out of the media bay.

1

CD/DVD drive

2

drive removal slot

3

M2.5 x 8-mm screw labeled " "

Installing the Optical Drive

  1. Slide the new drive into the bay until it snaps securely into place.

  2. Replace the M2.5 x 8-mm screw.

  3. Turn the computer right-side up and open the display.

  4. The operating system automatically recognizes the device. If necessary, enter your password to unlock your computer.

Mini PCI Card

Removing the Mini PCI Card

If you ordered a Mini PCI card with your computer, the card is already installed.

CAUTION: Before you begin any of the procedures in this section, follow the safety instructions in the Product Information Guide.
NOTICE: To avoid damaging the system board, you must remove the main battery before you begin working inside the computer.
  1. Follow the instructions in Before Working Inside Your Computer.

  2. Turn the computer over, loosen the captive screws on the memory module/Mini PCI cover, and then remove the cover.

 

 

1

captive screws (3)

 

 

  1. If a Mini PCI card is not already installed, go to step 1. If you are replacing a Mini PCI card, remove the existing card:

    1. Disconnect the antenna cable from the Mini PCI card.

 

 

1

antenna cable

 

 

    1. Release the Mini PCI card by spreading the metal securing tabs until the card pops up slightly.

    2. Lift the Mini PCI card out of its connector.

NOTICE: The connectors are keyed to ensure correct insertion. If you feel resistance, check the connectors and realign the card.

1

Mini PCI card

2

metal securing tabs (2)

 

 

Installing the Mini PCI Card

  1. Install the replacement Mini PCI card:

NOTICE: To avoid damaging the Mini PCI card, make sure the antenna cable is not under the card when you press the card into place.
    1. Align the Mini PCI card with the connector at a 45-degree angle, and press the Mini PCI card into the connector until it clicks.

1

Mini PCI card

2

metal securing tabs (2)

 

 

    1. Connect the antenna cable to the Mini PCI card. Make sure the cable snaps onto the primary connector on the Mini PCI card.

 

 

1

antenna cable

 

 

  1. Replace the memory module/Mini PCI cover and tighten the screws.

NOTICE: If the cover is difficult to close, remove the module and reinstall it. Forcing the cover to close may damage your computer.
  1. Insert the battery into the battery bay, or connect the AC adapter to your computer and an electrical outlet.

  2. Turn on the computer.

Back to Contents Page